Tips and tricks for cleaning

Pure water cleaning.
Wet glass. Clear results.

Why Jim leaves your freshly cleaned windows to dry naturally, and why the final rinse makes all the difference.

Those droplets are part of the process. With the dirt rinsed away and the residue-forming minerals removed from the cleaning water, there is no need to finish suitable exterior glass with a cloth or squeegee.

Jim cleaning an exterior window with a water-fed brush

Genuine photograph taken on The Street, Capel St Mary: Jim washes the glass with a water-fed brush, then gives it a thorough pure water rinse.

Why can pure water dry without leaving marks?

Ordinary tap water looks clear, but it contains dissolved mineral salts. When a droplet evaporates, the water leaves the surface while those dissolved solids can remain. On glass, that can show up as a white spot, a water mark or a visible drying trail.

Pure water cleaning tackles the water itself as well as the dirt on the window. Demineralising the rinse water removes the main ingredients of mineral spotting. The brush loosens the surface dirt and the rinse carries it away. Once the glass is properly clean, the remaining water can drain and evaporate without depositing the usual tap-water minerals.

No added detergent means there is no new soap or cleaning-product film to polish off. That is why the glass can be left wet at the end of the visit. UNGER explains the same wash, rinse and natural-drying principle in its professional pure water guidance.

The useful distinction: wet glass is not the finished result. Allow the remaining rinse water to dry before judging the clarity of the window.

From the brush to the finished window

Three stages. One natural drying process.

These are genuine photographs taken on The Street, Capel St Mary, showing the glass at different stages after cleaning and rinsing. Look at the water on the surface of the glass, rather than the reflections or the blinds behind it.

01 / JUST RINSED
Fresh pure water droplets on exterior window glass immediately after rinsing

Fresh water droplets

The brush has cleaned the window and the pure water rinse has washed the loosened dirt away. Small beads and droplets remain on the glass. Leave them to dry naturally. A cloth is not required for the exterior pure water finish.

02 / WHILE IT DRIES
Temporary wet trails visible on glass as the pure water rinse dries

Temporary wet trails

As the water drains and evaporates, some areas dry before others. For a few minutes you may see thin wet lines or streak-like effects. These are drying patterns in the remaining water, rather than proof that a permanent mark has been left behind.

03 / FULLY DRY
Dry window glass after pure water cleaning with no obvious droplets or drying trails

Clear, dry glass

Once the surface water has gone, the clean glass can be seen properly. The final photograph shows the clear finish, with no obvious remaining droplets or drying trails. There is no detergent film or tap-water mineral residue from the final pure water rinse to wipe away.

How long should I allow? In favourable conditions, glass may be dry in around 10 to 15 minutes. This is an indicative guide, not a fixed drying time or a timed test of these photographs. Temperature, humidity, airflow, shade and the amount of water remaining all affect the process. Cool, still or damp conditions can take longer.

The system comes with Jim

Pure water, generated in the van.

Kleenn brings the water supply, purification equipment and delivery system to the property.

Jim’s van carries the onboard pure water generation system, including filtration and resin, together with the water supply, pump, hose and long-reach poles. The cleaning water is processed through that system before it reaches the brush and the glass.

01 / SUPPLYWater carried onboard
02 / PURIFYFilters and resin
03 / DELIVERPump, hose and pole
04 / FINISHWash, rinse, air dry

That self-contained setup supports work on homes, business premises and suitable difficult-access glass. See how Jim and Kleenn are equipped for the job.

The technical bit, explained simply

What is pure water cleaning?

For window cleaning, “pure water” means water treated to have an extremely low level of dissolved mineral salts. It is usually produced by deionisation, reverse osmosis, or a combination of the two. The aim is a clean rinse that will not add mineral deposits as it dries.

What materials do purification systems use?

Sediment filters trap suspended particles. Activated carbon filters can reduce chlorine and protect a reverse osmosis membrane. A reverse osmosis membrane separates much of the dissolved salt content from the product water. Mixed-bed ion-exchange resin removes remaining dissolved ions through deionisation. Not every system uses every stage; this describes common professional designs rather than an unconfirmed specification for Jim’s equipment.

Xline’s filtration guide explains how RO and DI systems are selected for different source-water conditions. Filtration and resin need maintenance: exhausted treatment media can allow dissolved solids back into the cleaning water.

What does a 0 ppm TDS reading mean?

TDS stands for total dissolved solids, usually displayed in parts per million. A common professional target is a meter reading of 0 ppm. Handheld meters estimate dissolved ionic content from electrical conductivity. That is a useful process check, but a zero display is not laboratory proof that every possible substance is absent, nor does it establish drinking-water safety. The US EPA explains why conductivity responds to dissolved salts.

“Chemical-free” means no added cleaning chemicals in this method. Water itself is a chemical compound. The practical advantage is cleaning and rinsing suitable exterior glass without adding soap, detergent or a polishing product.

Why softened tap water is different

A domestic water softener generally exchanges calcium and magnesium for sodium. That reduces hardness, but dissolved salts remain. Softened water is therefore not automatically suitable for a spot-free final rinse. Demineralisation has a different objective: removing dissolved ions rather than simply exchanging the hardness minerals.

What minerals are normally in tap water?

The mixture varies by water source, local geology and supply zone. Common dissolved constituents include calcium, magnesium, sodium, potassium, bicarbonate, chloride, sulphate and silica. Nitrate and other dissolved substances can also contribute to the total. These are dissolved ions and compounds, rather than visible grains of rock.

Constituent Why it matters to the finish
Calcium and magnesium The main hardness minerals. Their salts can leave pale deposits and water spots when water evaporates. Calcium carbonate is familiar as limescale.
Bicarbonate and carbonate Part of the water’s alkalinity. Together with calcium and magnesium, these help explain carbonate deposits and scale.
Sodium and potassium Dissolved ions that contribute to TDS. Their salts can remain after evaporation even when water feels soft.
Chloride and sulphate Common dissolved anions, present with ions such as calcium, magnesium or sodium. The resulting salts contribute to residue if left to dry on glass.
Silica A naturally occurring dissolved constituent that can contribute to persistent mineral deposits. It is different from loose grit sitting on the window.
Iron and manganese Where present at elevated levels, these can cause coloured staining or discolouration. They are not the usual explanation for every white water spot.

On a small screen, scroll the table sideways to read both columns. The USGS overview of dissolved solids identifies the common constituents. The Drinking Water Inspectorate’s treatment manual explains hardness, iron and manganese.

The main concern for glass is the residue left by evaporation. Hardness minerals are a major reason ordinary tap-water droplets can dry as visible white marks. This is an appearance and cleaning issue; it does not mean normal drinking water is unsafe. Your supplier’s water-quality report gives the composition of your own supply, rather than a guessed local figure.

Pure water helps prevent fresh mineral spotting from the cleaning rinse. It does not automatically remove established limescale, scratches, damaged coatings or etched glass. Those need separate assessment. The Drinking Water Inspectorate’s hardness guidance explains the role of calcium and magnesium and how softening differs from removing dissolved solids.

The same principle, across different glass surfaces

Reducing mineral residue matters wherever a suitable glazed surface is washed and rinsed. The principle is shared; the brush, access, water delivery and surface-care requirements still need to suit the job.

Windows, rooflights and VELUX glass

For residential window cleaning, pure water can be used on suitable exterior windows, glazed doors and rooflights. The same final-rinse principle applies to accessible VELUX roof-window glass and suitable conservatory and roof glazing.

Coatings, seals, frames and access matter. VELUX’s own care guidance advises avoiding abrasive materials and applying water before attempting to remove dirt. The appropriate instructions for the particular window take priority.

Solar panels

Our solar panel cleaning service also uses the benefit of a low-mineral rinse on suitable installations. Removing surface deposits without adding mineral spots helps leave the panel glass clean.

Solar panels are electrical equipment, so they are assessed individually and cleaned in line with the manufacturer’s requirements. Canadian Solar’s cleaning guidance, for example, recommends water with low mineral content and suitable non-abrasive equipment. Cleaning is not an electrical inspection or a guarantee of a particular energy gain.

Shopfronts, bars, restaurants and commercial premises

The same approach can support a clear finish on suitable exterior display windows, entrance glazing and other business glass. For shops, bars, restaurants, pubs, cafés, offices, garages and showrooms, clean glass is part of presenting a well-maintained premises.

Explore our commercial cleaning services and commercial window cleaning. We agree the glass, frames, access and timing around the building and the people using it. Internal window cleaning is a separate service, with methods chosen to suit the indoor setting.

What should you do after a pure water clean?

Let the exterior glass dry by itself. Avoid wiping it with a household cloth or rinsing it again with a garden hose. A cloth can transfer lint or product residue, and untreated tap water can reintroduce the minerals the purification system removed.

If you still see a mark once the glass is fully dry, let Jim know which pane is affected. Residual dirt, old cleaning-product residue or water draining from a dirty frame can affect the finish. A streak between panes, a scratch or an established mineral stain is a different issue from water still evaporating.

For homes around Capel St Mary, Bentley, Wenham, Brantham, Copdock and suitable nearby areas, Kleenn offers one-off and recurring cleaning. Business enquiries are reviewed around Ipswich and the wider commercial service area. Check our areas covered and full range of exterior cleaning services for windows, gutters, solar panels, conservatory glazing, patios and driveways.

Talk to Jim

Clear glass starts with the right method.

Tell us what needs cleaning, your postcode and any difficult-access areas. Photographs help Jim understand the property and recommend the next step.

Kleenn on Facebook

Follow us on Facebook

Stay up to date with more tips and tricks, our latest news and any offers we have.

Visit our Facebook page

Sources and further reading

Technical explanations checked against professional equipment guidance, water-quality authorities and manufacturers’ care instructions. Service details reflect Kleenn’s own equipment and published service pages.